This shows you the differences between two versions of the page.
Next revision | Previous revision Next revision Both sides next revision | ||
en:plutotrx:operation [2021/06/03 14:36] dj0abr created |
en:plutotrx:operation [2021/09/18 18:39] dj0abr |
||
---|---|---|---|
Line 5: | Line 5: | ||
==== Spectrum and Waterfall ==== | ==== Spectrum and Waterfall ==== | ||
- | After correct configuration | + | After correctly configuring |
{{: | {{: | ||
Line 18: | Line 18: | ||
==== Frequency setting ==== | ==== Frequency setting ==== | ||
- | this is done with the mouse (or touchpad). | + | this is done with the mouse or a touch screen according to these two buttons: |
- | **left mouse click**: sets RX frequency on\\. | + | {{:de:plutotrx: |
- | **right mouse click**:sets RX and TX frequency | + | |
- | **mouse wheel**: changes frequency for fine tuning. | + | |
+ | | ||
+ | * RX and TX QRG active ... RX and TX frequency are adjusted. A possible offset between RX and TX remains unchanged. | ||
+ | * neither RX- nor TX-QRG ... there is no tuning. This is useful if you want to prevent accidental tuning. | ||
+ | |||
+ | So you select RX-QRG and/or TX-QRG and then click (tap) in the waterfall. | ||
+ | |||
+ | **Mouse | ||
**Common procedure: | **Common procedure: | ||
Line 29: | Line 35: | ||
first one selects the frequency in the upper spectrum/ | first one selects the frequency in the upper spectrum/ | ||
- | Now you go to the lower waterfall and do the fine tuning. Either | + | Now you go to the lower waterfall and do the fine tuning. Either |
Here is an example of a correctly tuned SSB signal. It is in the lower waterfall between the 0 and 3kHz line: | Here is an example of a correctly tuned SSB signal. It is in the lower waterfall between the 0 and 3kHz line: | ||
{{: | {{: | ||
- | If you also want to transmit, use the right mouse button, then both RX and TX frequency will be set equally. | ||
==== other controls ==== | ==== other controls ==== | ||
- | {{: | + | {{: |
- | * RIT ... the mouse wheel changes | + | * RX-QRG |
- | * XIT ... the mouse wheel changes | + | * TX-QRG |
* R>T ... the RX frequency is copied to the TX frequency | * R>T ... the RX frequency is copied to the TX frequency | ||
* T>R ... the TX frequency is copied to the RX frequency | * T>R ... the TX frequency is copied to the RX frequency | ||
- | * AGC ... increases | + | * AUDIO ... opens a window with settings for the microphone sensitivity (Mic-Boost should be set to 1 at first. Only if the sound is too quiet you can turn it up) and a bass boost. The bass boost is needed |
* MUTE ... reduces the volume in headphones or loudspeaker while transmitting. So you are no longer disturbed by listening back. Quietly one hears oneself for control purposes still. | * MUTE ... reduces the volume in headphones or loudspeaker while transmitting. So you are no longer disturbed by listening back. Quietly one hears oneself for control purposes still. | ||
- | * Compress ... switches the audio voice compressor on/off, 3 compression levels can be selected. The compressor makes the signal louder and more understandable, | + | * Compress ... switches the audio speech |
- | * RX and TX filters | + | * RX and TX Filter |
- | * Audio Loop ... The audio signal | + | * TX Bass ... affects the frequency response of the TX audio signal, if enabled, more bass can be heard. |
- | * RF Loop ... the Pluto receiver is set to its own transmit | + | |
+ | |||
+ | | ||
**PTT** ... Click to send (will turn red). Alternatively you can use the shift keys as PTT. | **PTT** ... Click to send (will turn red). Alternatively you can use the shift keys as PTT. | ||
Line 65: | Line 72: | ||
* Info ... Information about this program and license information. | * Info ... Information about this program and license information. | ||
- | ==== Audio volume ==== | + | ==== Audio Volume ==== |
+ | |||
+ | in many cases the default setting is ok. If you want to correct the volume | ||
+ | |||
+ | In addition to the volume setting, you have comfortable options for assigning audio devices. For example, you can switch the receive signal between the headphones or the speakers in the HDMI monitor without having to change the SETUP of the QO100 transceiver. | ||
+ | |||
+ | ==== Special functions | ||
+ | |||
+ | {{: | ||
+ | |||
+ | Screen icon ...setting of different screen resolutions to adapt the window to the monitor used. | ||
+ | |||
+ | CAL ... Menu for convenient setting of the correction values for the pluto and LNB reference frequency | ||
- | in many cases the default setting is ok. If you want to correct | + | LOCK/FREE ... Switching on and off the automatic beacon synchronization. When using a slow computer like Raspberry 3B+ the beacon synchronization must be switched off (FREE). |
- | Besides the volume control you have comfortable possibilities to assign audio devices. For example, you can switch | + | SAVE/ |